Collegamento elettrico condizionatore panasonic

#Collegamento elettrico condizionatore panasonic how to#
#Collegamento elettrico condizionatore panasonic install#
#Collegamento elettrico condizionatore panasonic full#
#Collegamento elettrico condizionatore panasonic series#

: Insulating The Refrigerant Tubing Heat Insulation For the flare nuts at tubing connections, be sure to use the.

#Collegamento elettrico condizionatore panasonic how to#

HOW TO PROCESS TUBING Caution Before Connecting Tubes Tightly (1) Apply a sealing cap or water-proof tape to prevent dust or The liquid tubing side is connected by a flare nut, and the gas water from entering the tubes before they are used.

: For Stranded Wiring How to connect wiring to the terminal в– For stranded wiring (1) Cut the wire end with cutting pliers, Stranded wire Special Screw then strip the insulation to expose washer the stranded wiring about 10 mm and Ring tightly twist the wire ends.

#Collegamento elettrico condizionatore panasonic install#

(2) Do not install the inter-unit control wiring in a way that forms a loop. (When shipping: In shorted condition.) For a system without link (no wiring connection between outdoor units), do not remove the short plug. CAUTION (1) When linking the outdoor units in a network, disconnect the terminal extended from the short plug from all outdoor units except any one of the outdoor units.2) * Single-phase model connections Power supply Ground 220/230/240V ~50Hz. 1) Power supply Outdoor unit (3-phase) 220/230/240V ~50Hz INV unit Power supply Ground Remote 380/400/415V, 3 N~, 50Hz controller Ground Ground Ground Indoor unit (No. Wiring System Diagrams * 3-phase model connections Indoor unit (No. General Precautions on Wiring Indoor unit (1) Before wiring, conп¬Ѓrm the rated voltage of the unit as (B) Power supply Time delay fuse or shown on its nameplate, then carry out the wiring closely Type circuit capacity 2.5 mm. Recommended Wire Length and Wire Diameter for Power Supply System 4-1. 3-6 height Open the ceiling board along the outer edge of the paper model. : Installing The Drain Pipe Keep the length of the bolt Down-slope Upward-slope from the bracket to 40 mm Air conditioner Ceiling body Air Trap No Air Trap Paper model for Set screw for paper installation Adjust to the same model (4 pieces) Fig.areas where leakage of flammable gas may be expected.Use a carpenterвЂ™s level to check AVOID: that the unit is level. Preparation for Ceiling Suspension This unit uses a drain pump. Please read over the entire set of instructions for the indoor and outdoor units and make sure all Deoxidized annealed copper tube for refrigerant tubing. Type of Copper Tube and Insulation Material If you wish to purchase these materials separately from a local This booklet briefly outlines where and how to install the source, you will need: air conditioning system. : Table Of Contents CONTENTS Page Page IMPORTANT!.work do not mix air except Modified or disassembled for specified refrigerant unit may cause fire, (R410A) in refrigeration electric shock or injury. When performing piping WARNING under any circumstances.This product must not be modified or disassembled WARNING.

#Collegamento elettrico condizionatore panasonic full#

Provide a power outlet exclusively for each unit, and full disconnection means Please Read Before Starting having a contact separation in all poles This air conditioner must be installed by the sales dealer must be incorporated in the fixed wiring or installer.

Indoor Units Rated Capacity Type Indoor Units Type S-36PY2E5A S-45PY2E5A S-50PY2E5A 4-Way Cassette 60Г—60 (CZ-KPY3A)* (CZ-KPY3A)* (CZ-KPY3A)* (CZ-KPY3B)* (CZ-KPY3B)* (CZ-KPY3B)* *Panel (optional parts) ENGLISH Read through the Installation Instructions before you proceed with the installation.

: Installation Instructions INSTALLATION INSTRUCTIONS вЂ“ Single Split Air Conditioner вЂ“ for Refrigerant R410A в– R410A Models Model No.

#Collegamento elettrico condizionatore panasonic series#

Summary of Contents for Panasonic CZ-KPY3A series